90° P-Trap Fuel Tank Vent - Black with Black Vent HeadThis Attwood 90-Degree P-Trap Fuel Tank Vent reliably helps prevent water from entering the fuel tank while still allowing air to vent freely during normal sea conditions and washdowns. This vent’s effectiveness eliminates the need for an anti-siphon loop in the vent hose. It requires a ¾-inch installation hole and can be used with a maximum hull thickness of 9/16 inches. Features:
Standard Mount - (inch) 5/8" I.D Hose
Reliably helps prevent water from entering the fuel tank
Still allows air to vent freely during normal sea conditions and washdowns
This black vent with a black vent head meets ABYC standards
*Compatible with Ethanol blended fuels. Quick Guide (pdf)
Deck Fill for Carbon Canister System - Straight Body & Scalloped Chrome CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Designed and tested to prevent water from entering the fuel system
Compatible with Ethanol blended fuels
Chrome finish
Automatic nozzle shutoff 4-18 gpm
Dual 1 psi overpressure relief safety valves built into the deck fill caps
EPA / CARB Certified
Quick Guide (pdf)
90° P-Trap Fuel Tank Vent - Black with Stainless Steel Trim CoverComposite 90-degree P-trap fuel tank vent 66419-3. These vents help prevent water from entering the fuel tank, yet allow air to vent freely, during normal sea conditions and washdowns. This eliminates the need for an anti-siphon loop in the vent hose. Features:
For 5/8" I.D. hose
(inch) 3/4" install. hole size
(inch) 9/16" max. hull thickness
Vents air from your boat's fuel tank as you fill the fuel tank
Splash-resistant, corrosion resistant
Meets ABYC standard
*Compatible with Ethanol blended fuels Quick Guide (pdf)
Deck Fill for Carbon Canister System - Angled Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
Fits 1-1/2 (inch) fill hose
Compatible with Ethanol blended fuels
Designed and tested to prevent water from entering the fuel system
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
EPA / CARB Certified
Dual 1 psi overpressure relief safety valves built into the deck fill caps
Automatic nozzle shutoff 4-18 gpm
Deck Fill for Carbon Canister System, angled, stainless steel, single pack
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Straight Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Designed and tested to prevent water from entering the fuel system
Compatible with Ethanol blended fuels
Stainless Steel finish
EPA / CARB Certified
Dual 1 psi overpressure relief safety valves built into the deck fill caps
Automatic nozzle shutoff 4-18 gpm
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Angled Body & Scalloped Chrome CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Compatible with Ethanol blended fuels
Designed and tested to prevent water from entering the fuel system
Automatic nozzle shutoff 4-18 gpm
Dual 1 psi overpressure relief safety valves built into the deck fill caps
EPA / CARB Certified
Deck Fill for Carbon Canister System, angled, chrome finish
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Angled Body & Scalloped Black Plastic CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Compatible with Ethanol blended fuels
Designed and tested to prevent water from entering the fuel system
Deck Fill for Carbon Canister System, angled, black composite
EPA / CARB Certified
Dual 1 psi overpressure relief safety valves built into the deck fill caps
Automatic nozzle shutoff 4-18 gpm
Quick Guide (pdf)
316 Stainless Steel Alloy Flush Mount Fuel Vent - Straight Vent On the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage or be damaged by hull bumps and scrapes. Cap unscrews with a hex head wrench for easy cleaning of the filter and pressure testing of the entire fuel system. These vents now include two silicone gaskets.Features:Straight VentSpecifications:
Hose Size (inch): 5/8" inner diameter
Maximum Hull Thickness (inch): 7/8"
Installation Hole Size (inch): 1-3/8"
*Includes two silicone gaskets Quick Guide (pdf)
316 Stainless Steel Alloy Flush Mount Fuel Vent - 90° VentOn the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage or be damaged by hull bumps and scrapes. Cap unscrews with a hex head wrench for easy cleaning of the filter and pressure testing of the entire fuel system. These vents now include two silicone gaskets.Features:90-degree ventSpecifications:
Hose Size (inch): 5/8" inner diameter
Maximum Hull Thickness (inch): 7/8"
Installation Hole Size (inch): 1-3/8"
*Includes two silicone gaskets Quick Guide (pdf)
MKR-28 Trolling Motor Plug & ReceptacleThe MKR-28 trolling Motor Plug and Receptacle provides continuous power and are rated to 60 amps up to 48V. Designed for freshwater and saltwater applications, silver-plated terminals provide reliable use in the harshest conditions. This plug is the recommended replacement for the MKR-18 Plug & Receptacle (part number 1865102) and MKR-26 (part number 1865128). Package includes: trolling motor plug with 18” wire lead, receptacle with 24” wire lead, mounting faceplate, dust cap, 1-10 AWG splicer, 1 AWG ferrule, 2 AWG ferrule, 4 AWG ferrule, heat shrink, hex wrench, and installation manual.Features:
Trolling Motor Plug and Receptacle provide continuous power rated to 60 amps up to 48V
Designed for freshwater and saltwater applications
Silver-plated terminals for a reliable corrosion-resistant connection in any freshwater or saltwater application
Sealed waterproof design
Secure threaded electrical connection
Adjustable mounting orientations
Continuous power rated to 60 amps up to 48V
8 AWG wire leads
Compatible with 1 - 10 AWG wire sizes
6" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates. Features:
Provides Improved Hole Shot
Reduces Water Drag at Take Off
Reduces Porpoising
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
10" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates. Features:
Provides Improved Hole Shot
Reduces Water Drag at Take Off
Reduces Porpoising
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
8" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates. Features:
Provides Improved Hole Shot
Reduces Water Drag at Take Off
Reduces Porpoising
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Adjustable Heavy-Duty Transom Saver - 24"-36"Protect your investment with Attwood Transom Savers. A lifted outboard puts hundreds of foot-pounds of pressure on the transom - especially during trailering.Features:
Support the cantilevered weight of the motor
Stabilize engine and steering mechanism when trailering
The Attwood Difference:Tough components - You'll get long life from our adjustable toggles with replaceable rubber pads
SWIVL-EZE LakeSport 2-3/8" Extension Post - 13" HighFixed height lake sport Series pedestal seat extension post 238613L1 is 13 inches high. A great extension post for 238 lake sport seat mounts and socket bases. For use on fishing, pontoon, or cruising boats to provide seat elevation. Attwood develops high-value, engineered marine products to make life on the water easier to enjoy. Made to meet the demands of boat builders and distribution partners, our products are extensively tested on-site in our lab to provide worry-free boating under all conditions.Features:
Hard anodized, corrosion-resistant aluminum seat pedestal
The locking latch has a low-friction ramped bottom for smooth Insertion into the base
The release button operates smoothly requiring less effort to unlock post from 238 series base
SELECT from Lake Sport series posts to get the perfect height for your boating fun
All Springs are stainless steel
Height measured from deck to top of seat mount
SWIVL-EZE LakeSport 2-3/8" Seat Mount with Friction Control - AluminumLakeSport Seat Mount is 2-3/8 inch Locking AO-Aluminum, with Friction Control, 3 Degree Tilt, ABYC Code - AO, Installed Height - 5/8 inch, Bulk Packaging. Hardware is Engineered to Exceed ABYC Standards Type A/Operator Models lead the industry with these features: Ergonomic positive-locking handles with stainless steel components inch-Slot inch locking channels (on adjustable-height models) are the safest manual adjustment available. All Models are reinforced for strength: All LakeSport posts are swaged and welded to the bases Bases have underside ribs for superior strength.
Troll-Tamer™ for Minn Kota Fortrex/Ultrex Trolling Motor Stabilizer Lock 5"-8" SpacingThe Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
Transom Support Plate Upper MountTransom Support Plate distributes stress of engine bolts. Cast in high quality aluminum. All plates are 3/8" thick. Fit top bolt pattern of outboard. Generic plate with no lettering is standard, but custom logos and black painting can be produced with minimum quantities. Features:
Distributes stress of engine bolts
High quality cast aluminum
All plates - 3/8" thick
Simple to install
Troll-Tamer™ for Minn Kota Fortrex Trolling Motor Stabilizer Lock 3-1/2"-5" Spacing The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
Oetiker Stepless Clamp Kit with PliersStepless™ 150-Piece Clamp Rigging Kit by T-H Marine®. This product is made of high-quality materials to serve you for years to come. Designed using state-of-the-art technology and with customers in mind, this product by T-H Marine® will last a lifetime. Features:
Plastic storage case contains 150 stainless steel Oetiker earless clamps, 10 each of 15 popular sizes, plus standard pincer installation tool
Oetiker hose clamps with mechanical interlock allows use of pre-coated materials
Specially formed strip edges reduce the risk of damage to the part being clamped with uniform compression and increased clamping force
All 304 stainless steel bands - Kit includes full size range for all marine hose
Includes:
(10) 5.8-7MM Ear Clamps
(10) 7.8 9.5MM Ear Clamps
(10) 8.8-10.5MM Ear Clamps
(10) 9.6-11.3MM Ear Clamps
(10) 11.5-14MM Ear Clamps
(10) 12-14.5MM Ear Clamps
(10) 13.2-15.7MM Ear Clamps
(10) 14.5-17MM Ear Clamps
(10) 15.3-18.5MM Ear Clamps
(10) 17.8-21MM Ear Clamps
(10) 22.4-25.6 Ear Clamps
(10) 26.9-30.1MM Ear Clamps
(10) 28.4-31.6MM Ear Clamps
(10) 37.8-41MM Ear Clamps
(1) Oetiker Jaw Pliers
(1) Plastic Tackle Tray
Transom Support Plate Lower MountFeatures:
10" Bolt Hole Pattern
Top Bolt Holes-Standard
3/8" Thickness. High quality Cast Aluminum
Distributes the stress of the motor mounting bolts
Troll-Tamer™ for Minn Kota Terrova & MotorGuide Trolling Motor Stabilizer Lock 5"-8" SpacingThe Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
Troll-Tamer™ for Minn Kota Fortrex Trolling Motor Stabilizer Lock 2-3/4"-4-1/2" Spacing The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
