Prop Master Propeller WrenchThe Prop Master™ is the original molded propeller wrench.This 1-1/16" six point socket style prop wrench is made of high tensile strength, indestructible nylon. It is totally resistant to fuel, sun, salt water, and other chemicals. The Prop Master™ is less expensive than metal wrenches which rattle and can cause damage to your boat. However, it has plenty of brawn to get the job done. The Prop Master™ will tighten all 1 1/16" propeller nuts without slipping or stripping. (OMC, Johnson and Evinrude, - over 40 HP, Mercury - over 50 HP) High visibility color makes it easy to locate in dark boat compartments. The Prop Master™ also has a 9/16" garboard drain plug socket on the reverse side. Will not corrode in the salt water environment.Features:
Fits All 1-1/16” Prop Nuts (40hp & up)
Rugged Nylon Resists Stripping
9/16” Garboard Drain Socket on Back
Non-Corrosive in Salt Environment
High Visibility Yellow makes wrench easy to find
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
Pitch: N/A
Material: Polymer
Diameter (Inches): 0.6875
Box Dimensions: 2"H x 6"W x 16"L WT: 0.6 lbs
UPC: 733572020007
PWC Anchor Kit - 3lb3 lb Grappling Folding AnchorFeatures:
Includes storage bag
For small boats, sailboats, personal watercraft, inflatables, and canoes
For sand, rock, mud, and gravel bottoms
Easy to deploy or stow away
Quick Flush Kit for OMC OutboardsProvides a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting the hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating water pressure keeps the valve sealed when using the engine. Features:
Makes flushing outboard quick and easy
Unique previously patented slide valve replaces the outboard flushing port plug
The O-ring seal closes off the port when operating the engine
Quick connect on hose snaps onto valve for flushing
No plug to remove and no difficulty turning of hose into the port
Takes the hassle out of flushing your outboard
Fits all outboards equipped with a flushing port
Kit consists of slide valve, hose quick connector, and washer
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
Type: Service Kits
Box Dimensions: 2"H x 4"W x 7"L WT: 0.1 lbs
UPC: 733572010602
Quick Flush™ Outboard Flush Fitting Kit for Mercury & Yamaha OutboardsProvides a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting the hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating water pressure keeps the valve sealed when using the engine. Features:
Makes flushing outboard quick and easy
Unique previously patented slide valve replaces the outboard flushing port plug
The O-ring seal closes off the port when operating the engine
Quick connect on hose snaps onto valve for flushing
No plug to remove and no difficulty turning of hose into the port
Takes the hassle out of flushing your outboard
Fits all outboards equipped with a flushing port
Kit consists of slide valve, hose quick connector, and washer
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
Type: Service Kits
Box Dimensions: 1"H x 4"W x 7"L WT: 0.1 lbs
UPC: 733572010626
Replacement Actuator for ATLAS™ Jack Plates Post March 2014Features:
Allows customers to remove the motor from a faulty AHJACT-3-DP and replacement it with a new one
More cost effective than replacing the entire actuator
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Replacement Relay Harness for Hydraulic Jack Plates 2014+Genuine Replacement Part for Atlas Hydraulic Jack Plate.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Scupper Flapper Repair KitThe flapper scupper repair kit should take care of any flapper replacement job. The traditional flapper scuppers use molded rubber flappers that curl and deform over time, requiring replacement to prevent leaking. Our flappers are not rubber, but are molded of a thermoplastic elastomer that is resistant to UV and the elements, so they do not curl like the rubber flappers.Repairs most scuppers with flappers, regardless of manufacturer.Kit Contains: All parts needed to repair 2 scuppers of a given size. Each kit contains 2 each of: 1-5/8" flappers, 1-7/8" flappers, and all necessary keepers and fasteners.
Steer Stop Outboard Hydraulic Steering Lock Set - 4"T-H Marine developed the first steering stop available for outboard motors and now we've revised that design so it stands apart from imitation and performs better than any other on the market. With our 4" Steer Stop Outboard Hydraulic Steering Lock in place, boaters can center their outboard motor equipped with hydraulic steering and keep it from wandering when trailering. Similar to the original Steer Stop, units clip onto hydraulic steering rams on either side of outboard to keep engine straight and prevent damage to motor supports. The cord then keeps units together when stowed and aids removal.Additionally, with the new grip built into the design, it is easier than ever to install and remove the Steer Stop Outboard Hydraulic Steering Lock, saving you effort and wear and tear on your hands.Features:
Must-know information about the 4" Steer Stop Outboard Hydraulic Steering Lock:
Locks hydraulic steering when trailering
Fits most steering cylinder rods on outboard engines
Snaps over outboards hydraulic steering cylinder rods
Helps keep engine centered during transport
Protects steering system, outboard, and motor supports
Includes cord to connect units for storage and to aid in removal
Grip makes it even simpler and easier to put on and take off
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
Type: Tools
Box Dimensions: 2"H x 5"W x 7"L WT: 0.45 lbs
UPC: 733572206708
Steering Trim Control UnitTrim Switches on the Steering Wheel Improve Safety and Performance. This steering trim control unit is molded of black plastic with raised white letters to not only enhance boat appearance but also provide the ultimate in control of any high performance boat. The steering trim control unit mounts easily to steering wheel spokes to place engine trim control at your finger tips for maximum safety and ease of operation. The weather proof, rubber booted, push button switches combined with a black urethane coiled cord provide a unit which will provide trim control without removing hands from steering wheel.Features:
Puts trim switches on steering wheel for convenience and safety
Allows driver to keep both hands on the steering wheel
Mounts easily on steering wheel spokes
Weatherproof rubber booted switches
Rugged urethane coiled cord
Can be used for trim control or jack plate control
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
Type: Switches
Box Dimensions: 2"H x 5"W x 7"L WT: 0.6 lbs
UPC: 733572001105
Straight Barbed All-Purpose Drain - White1-3/8" White Concaive Head Drain. These molded drains, available in straight and 90-degree versions, offer a low-cost method to drain water from virtually anywhere. They have a very low-profile concave head to allow complete drainage. Drains mount easily in a 1-3/8" diameter hole and are secured with the molded nut that is included. Hose barbs fit a 3/4" hose for routing of drainage.Specifications:
Color: White
Fits Hole Diameter: 1-3/8"
Water Connection: 3/4" Hose
T-H FLEX™ 1-1/2" Expandable Braided Sleeving - 50' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features:
Lightweight Protective Sleeving
Protects Wire, Cables and Hoses
Braided from High Temperature Yarns
Chemical Resistant
Simplifies and beautifies any rigging application
Specifications:
Type: Misc
Box Dimensions: 6"H x 9"W x 10"L WT: 1.7 lbs
UPC: 733572036800
T-H FLEX™ 1-1/4" Expandable Braided Sleeving - 50' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features:
Lightweight Protective Sleeving
Protects Wire, Cables and Hoses
Braided from High Temperature Yarns
Chemical Resistant
Simplifies and beautifies any rigging application
Specifications:
Type: Misc
Box Dimensions: 6"H x 9"W x 10"L WT: 1.45 lbs
UPC: 733572036756
T-H FLEX™ 1/2" Expandable Braided Sleeving - 100' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features:
Lightweight Protective Sleeving
Protects Wire, Cables and Hoses
Braided from High Temperature Yarns
Chemical Resistant
Simplifies and beautifies any rigging application
Specifications:
Type: Misc
Box Dimensions: 6"H x 9"W x 10"L WT: 1.5 lbs
UPC: 733572036657
T-H FLEX™ 1/4" Expandable Braided Sleeving - 100' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features:
Lightweight Protective Sleeving
Protects Wire, Cables and Hoses
Braided from High Temperature Yarns
Chemical Resistant
Simplifies and beautifies any rigging application
Specifications:
Type: Misc
Box Dimensions: 6"H x 9"W x 10"L WT: 0.85 lbs
UPC: 733572036602
T-H FLEX™ 2" Expandable Braided Sleeving - 50' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features:
Lightweight Protective Sleeving
Protects Wire, Cables and Hoses
Braided from High Temperature Yarns
Chemical Resistant
Simplifies and beautifies any rigging application
Specifications:
Type: Misc
Box Dimensions: 6"H x 9"W x 10"L WT: 2 lbs
UPC: 733572036855
T-H FLEX™ 3/4" Expandable Braided Sleeving - 100' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features:
Lightweight Protective Sleeving
Protects Wire, Cables and Hoses
Braided from High Temperature Yarns
Chemical Resistant
Simplifies and beautifies any rigging application
Specifications:
Type: Misc
Box Dimensions: 6"H x 9"W x 10"L WT: 1.75 lbs
UPC: 733572036701
Toggle Anchor KitGame-changing hardware for mounting trolling motors and table and seat pedestals, especially on decks and bulkheads where access is limited. Secures any accessory that will receive a high amount of torque at the fastening location. Features:
Stainless steel toggle 2” long x 0.45” wide
Accepts ¼”-20 fasteners
Requires a ½” mounting hole
Great for tables, seat bases, and trolling motors
Transom Support Plate Lower MountFeatures:
10" Bolt Hole Pattern
Top Bolt Holes-Standard
3/8" Thickness. High quality Cast Aluminum
Distributes the stress of the motor mounting bolts
Transom Support Plate Upper MountTransom Support Plate distributes stress of engine bolts. Cast in high quality aluminum. All plates are 3/8" thick. Fit top bolt pattern of outboard. Generic plate with no lettering is standard, but custom logos and black painting can be produced with minimum quantities. Features:
Distributes stress of engine bolts
High quality cast aluminum
All plates - 3/8" thick
Simple to install
Transom Trim Control Push Button Trim SwitchTransom Trim Control Switch/Hydraulic Jack Plate SwitchPut a trim switch or hydraulic jack plate anywhere you want with this versatile switch. The Transom Trim Control Switch provides a weatherproof tilt control system at the stern area of the boat to facilitate placing motor support in position with one person. Switch can also be used for remote adjustment of hydraulic jack plates. The switch housing is molded black plastic with raised white letters and may be mounted on any flat surface, comes with 18" pigtail wire and installation instructions.Features:
Trim switch for outboards or stern drives
Hydraulic jack plate switch
Puts Tilt & Trim Control Anywhere
Weatherproof Control Switches
UV stable molded housing
Can Also Operate Power Jack Plates
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Troll-Tamer™ for Minn Kota Fortrex Trolling Motor Stabilizer Lock 2-3/4"-4-1/2" Spacing The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
Troll-Tamer™ for Minn Kota Fortrex Trolling Motor Stabilizer Lock 3-1/2"-5" Spacing The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
Troll-Tamer™ for Minn Kota Fortrex/Ultrex Trolling Motor Stabilizer Lock 5"-8" SpacingThe Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
Troll-Tamer™ for Minn Kota Terrova & MotorGuide Trolling Motor Stabilizer Lock 5"-8" SpacingThe Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditionsThe latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.
