Fuel Tank Strap Set - 48 (inches) Long for 3-6 Gallon TanksThis Attwood Fuel Tank Strap Set contains everything needed to secure a 3-6-gallon fuel tank in place. This kit includes a 48-inch-long, 1-inch-wide white nylon web strap with a zinc-plated carbon steel snap and quick-release buckle. There are also 2 metal footman securing loops and the screws needed to install them. The strap can be run through the footman openings and then tightened and buckled to hold the tank in place.Features:
Includes 48-inch-long, 1-inch-wide white nylon web strap with a zinc-plated carbon steel snap and quick-release buckle
Run the strap through footman loops, then tighten and buckle to hold the tank in place
Quick Guide (pdf)
Motor Well Boot for 4 (inch) Diameter OpeningThe motor well boot provides an organized, covered pass-thru for control cables, wires, or fuel lines. The split side allows for installation without disconnecting controls.Features:
Sold as a single pack that contains two Motor Well Boots
Includes ties for a secure fit
Black rubber, UV-resistant construction with polypropylene attachment gasket ring
*Designed for a 4-inch diameter opening
Deck Fill for Pressure Relief Systems - Angled Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling.Features:
Fits 1-1/2 (inch) fill hose and 5/8 (inch) vent hose
Triple high-flow vacuum valves ensure maximum make-up airflow (compatible with high HP applications)
Dual 1 psi diurnal emission control and overpressure relief safety valves built into the cap
Automatic nozzle shutoff 4-18 gpm
Stainless Steel finish
An essential component of VaporTec and SecureStop
Designed and tested to prevent water from entering the fuel system
EPA / CARB Certified
Hinged audible click cap meets EPA requirements
Meets CARB 13 CCR 2235 and ISO 13331 nozzle mating and retention standards
*Compatible with Ethanol blended fuels Quick Guide (pdf)
Deck Fill for Pressure Relief Systems - Angled Body & Scalloped Black Plastic CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling.Features:
Fits 1-1/2 (inch) fill hose and 5/8 (inch) vent hose
Triple high-flow vacuum valves ensure maximum make-up airflow (compatible with high HP applications)
Dual 1 psi diurnal emission control and overpressure relief safety valves built into the cap
Automatic nozzle shutoff 4-18 gpm
Black Composite finish
An essential component of VaporTec and SecureStop
Designed and tested to prevent water from entering the fuel system
EPA / CARB Certified
Hinged audible click cap meets EPA requirements
Meets CARB 13 CCR 2235 and ISO 13331 nozzle mating and retention standards
*Compatible with Ethanol blended fuels Quick Guide (pdf)
Deck Fill for Pressure Relief Systems - Straight Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling.Features:
Fits 1-1/2 (inch) fill hose and 5/8 (inch) vent hose
Triple high-flow vacuum valves ensure maximum make-up airflow (compatible with high HP applications)
Automatic nozzle shutoff 4-18 gpm
Stainless Steel finish
An essential component of VaporTec and SecureStop
Designed and tested to prevent water from entering the fuel system
EPA / CARB Certified
Hinged audible click cap meets EPA requirements
Meets CARB 13 CCR 2235 and ISO 13331 nozzle mating and retention standards
*Compatible with Ethanol blended fuels Quick Guide (pdf)
Standard Carbon CanisterCarbon canister systems utilize an engineered charcoal canister to reduce hydrocarbons entering the atmosphere. Other components of a carbon canister system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood carbon canister systems are designed to ensure liquid fuel or water does not reach the canister and are compatible with Jerry Can and marine nozzle refueling.Features:
Brackets OEM Installed
Low permeation shell reduces overall system emissions
Can be mounted in any orientation using brackets provided
EPA / CARB Certified
Fits a 5/8" vent hose
Specifications:
Trailerable Vessel Capacity (EPA Rating): 220 Gallon
Non-Trailerable Vessel Capacity (EPA Rating): 350 Gallon
Trailerable Vessel Capacity (CARB Rating): 176 Gallon
Non-Trailerable Vessel Capacity (CARB Rating): 350 Gallon
*Compatible with Ethanol blended fuels Quick Guide (pdf)
Compact Carbon CanisterCarbon canister systems utilize an engineered charcoal canister to reduce hydrocarbons entering the atmosphere. Other components of a carbon canister system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood carbon canister systems are designed to ensure liquid fuel or water does not reach the canister and are compatible with Jerry Can and marine nozzle refueling.Features:
This is a single pack that contains two Compact Carbon Canisters
Brackets OEM Installed
Low permeation shell reduces overall system emissions
Can be mounted in any orientation using brackets provided
EPA / CARB Certified
Fits a 5/8" vent hose
Specifications:
Trailerable Vessel Capacity (EPA Rating): 70 Gallon
Non-Trailerable Vessel Capacity (EPA Rating): 110 Gallon
Trailerable Vessel Capacity (CARB Rating): 56 Gallon
Non-Trailerable Vessel Capacity (CARB Rating): 110 Gallon
*Compatible with Ethanol blended fuels Quick Guide (pdf)
90° P-Trap Fuel Tank Vent - Flush Mount - Black with Stainless Steel Vent HeadThis Attwood 90-Degree P-Trap Fuel Tank Vent reliably helps prevent water from entering the fuel tank while still allowing air to vent freely during normal sea conditions and washdowns. This vent’s effectiveness. eliminates the need for an anti-siphon loop in the vent hose. This is a flush mount vent for use with a 5/8-inch interior diameter hose. It requires a 1-3/8-inch installation hole and can be used with a maximum hull thickness of 1 inch.Features:
This black vent with a stainless steel vent head meets ABYC standards
Flush Mount - 5/8" I.D. hose
(inch) 1-3/8" install. hole size
(inch) 1" Max. hull thickness
*Compatible with Ethanol blended fuels Quick Guide (pdf)
90° P-Trap Fuel Tank Vent - Black with Black Vent HeadThis Attwood 90-Degree P-Trap Fuel Tank Vent reliably helps prevent water from entering the fuel tank while still allowing air to vent freely during normal sea conditions and washdowns. This vent’s effectiveness eliminates the need for an anti-siphon loop in the vent hose. It requires a ¾-inch installation hole and can be used with a maximum hull thickness of 9/16 inches. Features:
Standard Mount - (inch) 5/8" I.D Hose
Reliably helps prevent water from entering the fuel tank
Still allows air to vent freely during normal sea conditions and washdowns
This black vent with a black vent head meets ABYC standards
*Compatible with Ethanol blended fuels. Quick Guide (pdf)
Deck Fill for Carbon Canister System - Angled Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
Fits 1-1/2 (inch) fill hose
Compatible with Ethanol blended fuels
Designed and tested to prevent water from entering the fuel system
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
EPA / CARB Certified
Dual 1 psi overpressure relief safety valves built into the deck fill caps
Automatic nozzle shutoff 4-18 gpm
Deck Fill for Carbon Canister System, angled, stainless steel, single pack
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Angled Body & Scalloped Chrome CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Compatible with Ethanol blended fuels
Designed and tested to prevent water from entering the fuel system
Automatic nozzle shutoff 4-18 gpm
Dual 1 psi overpressure relief safety valves built into the deck fill caps
EPA / CARB Certified
Deck Fill for Carbon Canister System, angled, chrome finish
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Angled Body & Scalloped Black Plastic CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Compatible with Ethanol blended fuels
Designed and tested to prevent water from entering the fuel system
Deck Fill for Carbon Canister System, angled, black composite
EPA / CARB Certified
Dual 1 psi overpressure relief safety valves built into the deck fill caps
Automatic nozzle shutoff 4-18 gpm
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Straight Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Designed and tested to prevent water from entering the fuel system
Compatible with Ethanol blended fuels
Stainless Steel finish
EPA / CARB Certified
Dual 1 psi overpressure relief safety valves built into the deck fill caps
Automatic nozzle shutoff 4-18 gpm
Quick Guide (pdf)
Deck Fill for Carbon Canister System - Straight Body & Scalloped Chrome CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features:
All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling
Fits 1-1/2 (inch) fill hose
Designed and tested to prevent water from entering the fuel system
Compatible with Ethanol blended fuels
Chrome finish
Automatic nozzle shutoff 4-18 gpm
Dual 1 psi overpressure relief safety valves built into the deck fill caps
EPA / CARB Certified
Quick Guide (pdf)
3/8" Hose Mender In-Line Fuel Splice Kit with Stainless Steel ClampsWhether it’s an emergency situation on the water or routine maintenance at the dock, this in-line fuel splice kit provides everything you need to repair 3/8-inch lines. Machined brass fitting paired with 2 stainless steel hose clamps. Features:
Everything you need to mend a 3/8-inch fuel line including 2 stainless steel hose clamps
Solid machined brass with barbed ends
A centered divider ensures you get the mender evenly and securely placed between both ends of the hose
Very Versatile: Use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels
Quick Guide (pdf)
Universal Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" BarbThis Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line.Features:Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuelsSpecifications:
Material Construction: Aluminum
Male thread, hose barb
(inch) Male 3/8" NPT x 3/8" Barb
*Use thread sealant on all threads Quick Guide (pdf)
Universal Brass Fuel Hose Fitting - 1/4" NPT x 3/8" Barb This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line.Features:
Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels
Material Construction: Brass
Male thread, hose barb
(inch) Male 1/4" NPT x 3/8" Barb
*Use thread sealant on all threads Quick Guide (pdf)
Universal Brass Fuel Hose Fitting - 1/4" NPT x 5/16" Barb This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line.Features:
Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels
Material Construction: Brass
Male thread, hose barb
(inch) Male 1/4" NPT x 5/16" Barb
*Use thread sealant on all threads Quick Guide (pdf)
Tsunami MK2 T500 Manual Bilge Pump with Installation Kit - 500 GPH & 12VThis is a complete kit (includes a bilge pump) to install a manual bilge pump with a 3/4" I.D. hose outlet. The Tsunami Mk2 is the only manual bilge pump that eliminates airlocks. This is done by the Patented X-Air™ Impeller, which ejects trapped air in the pump and pipework. Also, the Tsunami Mk2 is the most reliable manual bilge pump in freshwater applications, considering it has 40% better protection against water ingress and electrolysis vs. the Mk1 pump. Kit Includes:
Attwood Tsunami Mk2 500 GPH Pump
Washer / Non-Return Valve
90-degree Outlet
Straight Outlet
3/4" x 5' Pump Hose
3/4" Thru-hull fitting
2-way on/off switch with bezel plate
Snap-It hose clamps
Wire Kit
Installation Kit
Easy Installation & Service:
GPH (Gallons Per Hour): 500 GPH
90° rotatable elbow outlet allows users to install the pump anywhere in a full 360° orientation
Backward compatible hole pattern and motor cartridges of Tsunami Mk1 bilge and aerator pumps
External mounting feet and integrated outlets reduce time and effort
Service pump cartridges from hard-to-reach areas using only one hand
Specifications:
Rated Volts DC: 12VDC
Fuse Size: 3 AMP
Wire Length: (inch) 29" / (mm) 735mm
Hose Diameter: (inch) 3/4" and 1"
*Caution: Bilge pump switches are not external ignition protected Specifications:
Gallons Per Hour: 500 GPH
Operation: Non-Automatic
Outlet Size: 3/4" or 1"
Type: Electric
Volts: 12v
Box Dimensions: 6"H x 7"W x 9"L WT: 1.75 lbs
UPC: 022697024213
Quick Guide (pdf)
Kayak Hand Bilge Pump This Attwood Hand-Operated Bilge Pump quickly and safely removes unwanted water and other liquids from small craft such as kayaks, canoes, and small fishing boats. This pump can remove up to 8 gallons per minute, and no hose is required. The pump is an 18-inch-long pump and has an ergonomic hand grip that keeps the pump afloat if dropped into the water.Features:
Ideal for small craft such as kayaks, canoes, and small fishing boats
(inch) 18" long
Sturdy, impact-resistant, and lightweight plastic construction
*No hose is required Specifications:
Gallons Per Minute: 8 GPM
Operation: Non-Automatic
Type: Manual
Box Dimensions: 4"H x 4"W x 21"L WT: 3.7 lbs
UPC: 022697115959
LightArmor All-Round 24" Navigation Light for PowerbaseOn boats under 12 m (39 ft), the All-round light must be located a minimum of one meter above the red-green sidelights, measured at the center of the light source of the appliances. Also, this navigation light can be adjusted for angled applications.Features:
(inch) 24" All-Round Pole Light
Articulating head adjusts from 15° fore to 15° aft (at, near, or toward the stern of a ship)
Rated for 50,000 hours of use
5-year warranty
Two miles 360º light visibility for boats up to 12 m (39 ft)
Meets ABYC & USCG requirements and all applicable standards
*Compatible only with the Attwood PowerBase (6100-LT-7) Specifications:
LED: Yes
Lens Color: White
Box Dimensions: 2"H x 4"W x 25"L WT: 0.35 lbs
UPC: 022697024480
Suzuki 3/8" Barb Female Hose Fitting - Under 75HPQuick-connect female fitting for use on both ends of fuel lines to connect to tank fitting and engine. Fuel tank fittings and hose fittings are suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels. The barb fitting fits a 3/8" I.D. hose. Also, clamps are not included, and use thread sealant on all threads.Features:
Suzuki-brand engines and tanks
Fitted for models under 75HP (Small Bore)
Material Construction: Chrome-plated Brass
*Specifically mates to Attwood part number: 14509-6 Quick Guide (pdf)
Chrysler Female Hose Fitting - 3/8" BarbThis Attwood Chrysler Engine Fuel Hose Fitting provides for the precise and effective installation of a fuel line to a Chrysler-brand engine. This Fuel Hose Fitting is a female fitting that connects to the engine end of the fuel line. The fitting has a 3/8-inch barb.Features:
Provides precise installation of a fuel line to a Chrysler-brand engine
Connects on the engine end of the fuel line
Material Construction: Chrome-plated Brass
*Specifically mates to Attwood part number: 14509-6 Quick Guide (pdf)
Chrysler/Suzuki Tank Fitting - 1/4" NPT ThreadThis Attwood Fuel Tank Male Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels. This threaded fitting has a 1/4" male NPT thread. Also, use thread sealant on all threads, and clamps are not included.Features:
Male tank fitting designed for Chrysler & Suzuki engines and fuel tanks
Designed for Under 75HP (Small Bore)
Material Construction: Chrome-plated Brass
*Specifically mates to Attwood part numbers: 8884-6 & 88FTS014-6 Quick Guide (pdf)
